Search found 782 matches
- Sun Jan 21, 2024 5:06 pm
- Forum: Support Requests
- Topic: Learnir V2 doesn`t work with analysir
- Replies: 6
- Views: 5608
Re: Learnir V2 doesn`t work with analysir - Solved
Solved: Final solution was to upgrade to latest release, which supports the new BAUD rate for LearnIR.
- Sun Jan 21, 2024 4:41 pm
- Forum: Support Requests
- Topic: Learnir V2 doesn`t work with analysir
- Replies: 6
- Views: 5608
Re: Learnir V2 doesn`t work with analysir
I just did a quick check and did not see any order from you for AnalysIR. If you did make an order for AnalysIR, please email the reference directly to support@....com (do not post here) The app you downloaded only runs in demo mode (before registration) and this would explain why it didnt work for ...
- Sun Jan 21, 2024 1:15 pm
- Forum: Support Requests
- Topic: Learnir V2 doesn`t work with analysir
- Replies: 6
- Views: 5608
Re: Learnir V2 doesn`t work with analysir
In AnalysIR, Menu->File->Serial Port->Set BAud Rate->250000
The BAud Rate will then be remembered for future settings.
Make sure you have updated to the latest release....9445 or later. (Link was sent by email after purchase)
The BAud Rate will then be remembered for future settings.
Make sure you have updated to the latest release....9445 or later. (Link was sent by email after purchase)
- Sat Jan 20, 2024 3:13 pm
- Forum: Support Requests
- Topic: Learnir V2 doesn`t work with analysir
- Replies: 6
- Views: 5608
Re: Learnir V2 doesn`t work with analysir
Have you changed the default BAUD rate in AnalysIR to 250000bps?
- Wed Aug 09, 2023 12:41 pm
- Forum: IR Protocols & Codes
- Topic: NIBE AC Protocol
- Replies: 3
- Views: 7124
Re: NIBE AC Protocol
Thanks, I got the session file and after checking it out....I cannot find any obvious pattern for the checksum. Using LSB8, the checksum is clearly in the last 2 nibbles. However the encoding is not obvious.It may just be a subset of bits in the these nibbles. If I were to guess, it is more likely a...
- Mon Aug 07, 2023 8:39 pm
- Forum: IR Protocols & Codes
- Topic: NIBE AC Protocol
- Replies: 3
- Views: 7124
Re: NIBE AC Protocol
Please send a saved session file (Menu->File->Save Session) to me at info@Analysir.......etc
I will then have a look at it. Given the 90 bits makes it more difficult & would [NOT] work well with the checksum calculator by default.
I will then have a look at it. Given the 90 bits makes it more difficult & would [NOT] work well with the checksum calculator by default.
- Sat Jul 22, 2023 4:12 pm
- Forum: IR Protocols & Codes
- Topic: Homemade AC-controller
- Replies: 9
- Views: 7379
Re: Homemade AC-controller
@Debojitk
Please read the thread and in particular my second reply above!
Please read the thread and in particular my second reply above!
- Sat Jul 22, 2023 4:07 pm
- Forum: IR Protocols & Codes
- Topic: Homemade AC-controller
- Replies: 9
- Views: 7379
Re: Homemade AC-controller
@Ripen I see at least 2 possible issues. Your emitter module has a 220R resistor in line, which means you will get very little IR transmitted when you are driving it directly from the GPIO pin. Your IR receiver is among the worst you could get (That is why they are so cheap). It could also be the re...
- Mon Jul 10, 2023 8:05 pm
- Forum: IR Protocols & Codes
- Topic: Homemade AC-controller
- Replies: 9
- Views: 7379
Re: Homemade AC-controller
No...it is always 944nm for IR remote control. Use sendRAW until you get it working. the sizeof...just automatically calculates teh buffer size. Instead of NEC_KHZ try 38. and also try values for 36 & 33 to see if it makes a difference. Most ACs are 38kHz What are you using to send? Post a photo...
- Sun Jul 09, 2023 12:28 pm
- Forum: IR Protocols & Codes
- Topic: Homemade AC-controller
- Replies: 9
- Views: 7379
Re: Homemade AC-controller
uint16_t rawData[99] Try increasing the max/default buffer size in IRremote as it is possible you might not be getting the full signal captured. set using RAW_BUFFER_LENGTH increase it in steps of 100 until the 99 above is less than teh value you set -1 You may have to restart teh IDE to force the c...