Search found 792 matches

by AnalysIR
Wed Aug 14, 2024 4:16 pm
Forum: IR Protocols & Codes
Topic: Help to Getting IR Code Protocol Panasonic AC
Replies: 1
Views: 3335

Re: Help to Getting IR Code Protocol Panasonic AC

First of all the signal you posted are the RAW signals, on first look. I uploaded them toour AnalysIR app and they look like the following (essentially the same signal) 2024-08-14 17_12_59_ScreenShot.jpg However, they might have been truncated by you capture system. I cannot offer anymore unless you...
by AnalysIR
Tue Aug 06, 2024 12:12 pm
Forum: IR Protocols & Codes
Topic: Help getting info on this LG AC IR Protocol (>170 bits)
Replies: 3
Views: 2391

Re: Help getting info on this LG AC IR Protocol (>170 bits)

Quick question, does the reverse engineering tool come with the Analysir software? Also does the Analysir software run on Linux? Yes, all features are the same on all editions. The editions only vary by usage. (commercial, non-commercial & Edu) Also does the Analysir software run on Linux? NO, ...
by AnalysIR
Mon Aug 05, 2024 2:37 pm
Forum: IR Protocols & Codes
Topic: Help getting info on this LG AC IR Protocol (>170 bits)
Replies: 3
Views: 2391

Re: Help getting info on this LG AC IR Protocol (>170 bits)

HI Bill Based on a sample of 1 signal it appears the checksum is the last byte (9A) using LSB8 format (reverse your byte bit order). The checksum is the sum of all bytes except the last one which is the actual checksum. I have included an image showing this info. Using our reverse engineering tool i...
by AnalysIR
Sun Aug 04, 2024 7:25 pm
Forum: IR Protocols & Codes
Topic: Mitsubishi MSZ-FH
Replies: 8
Views: 12470

Re: Mitsubishi MSZ-FH

OK I tried 2 signals & it seems it is the sum of all bytes except the last = the last byte = checksum.

However the bit order of each byte is LSB8 (reversed)
2024-08-04 20_23_58-AnalysIR 1.19.200.9446.jpg
by AnalysIR
Wed Jul 31, 2024 6:40 pm
Forum: IR Protocols & Codes
Topic: Mitsubishi MSZ-FH
Replies: 8
Views: 12470

Re: Mitsubishi MSZ-FH

I had a quick look and it proved to be a new protocol, which I added to AnalysIR. # bits =144 or 18 bytes + headers + trailers To get checksum ignore first & last byte and then do a sum on all the nibbles. (I only checked 1 signal so could be wrong?) 2024-07-31 19_34_51-Checksum Calculator.png Y...
by AnalysIR
Tue Jul 30, 2024 7:36 pm
Forum: IR Protocols & Codes
Topic: Mitsubishi MSZ-FH
Replies: 8
Views: 12470

Re: Mitsubishi MSZ-FH

please post the full signals in RAW format & I will have a look.
by AnalysIR
Sat Jul 06, 2024 9:06 pm
Forum: IR Protocols & Codes
Topic: How are delta values calculated for each protocol?
Replies: 1
Views: 2917

Re: How are delta values calculated for each protocol?

It is arbitrary based on experience. Nominally your 601 uSec signal(Mark) would not be recognized. However, if you use the Tolerance slider on the GUI you can vary the tolerance at any time. The original basis was related to accuracy of IR receivers being +/- 100uSecs (actually up to 200uSecs). Usua...
by AnalysIR
Fri Jun 21, 2024 12:11 pm
Forum: IR Protocols & Codes
Topic: Sending RAW IR signal by bit
Replies: 5
Views: 4740

Re: Sending RAW IR signal by bit

As I suggested earlier your code needs a major redo. You are running thru every if statement for each bit(so 200 times 8 if compares). Use the else if approach so that only one comparison is made for each bit The most common occurrence should be the first if statement and so on. This should be your ...
by AnalysIR
Wed Jun 19, 2024 11:44 am
Forum: IR Protocols & Codes
Topic: Sending RAW IR signal by bit
Replies: 5
Views: 4740

Re: Sending RAW IR signal by bit

Some tips: - to debug replace the IrSender.mark(MARK_DURATION); IrSender.space(SHORT_DELAY); with serial print statements to see/verify if your logic is correct. - make use of else if statements to avoid multiple checks for every bit - then I would either use an index into a buffer to get the timing...
by AnalysIR
Wed Jun 12, 2024 4:37 pm
Forum: IR Protocols & Codes
Topic: Sending RAW IR signal by bit
Replies: 5
Views: 4740

Re: Sending RAW IR signal by bit

look at some examples in our blog

https://www.analysir.com/blog/2016/04/1 ... -irremote/

https://www.analysir.com/blog/2015/09/0 ... r-signals/

You may get some inspiration from the above or other posts under sitemap.